Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| product_overview:front_panel [2010/11/03 13:41] – tibor | product_overview:front_panel [2011/08/17 10:16] (current) – tibor | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Front Panel ====== | ====== Front Panel ====== | ||
| + | ===== Indicators ===== | ||
| + | There are several lamps indicating interface status: | ||
| ^ Indicators: ^^ | ^ Indicators: ^^ | ||
| | AIR | Wireless (802.11b/g) | | | AIR | Wireless (802.11b/g) | | ||
| - | | PH1 and PH2 | First and second telephone port (FXS) indicator | + | | PH1 and PH2 | First and second telephone port (FXS) indicator\\ OFF – Phone not registered\\ Steady GREEN – Phone registered\\ Flashing RED – Dialing\\ Steady RED – In use\\ GREEN / RED flashing – Message waiting\\ RED strobe (1.3s off and 0.3s on) – Unavailable | |
| - | | ::: | OFF – Phone not registered | + | | LINE | Telephony gateway |
| - | | ::: | Steady GREEN – Phone registered | + | |
| - | | ::: | Flashing RED – Dialing | + | |
| - | | ::: | Steady RED – In use | | + | |
| - | | ::: | GREEN / RED flashing – Message waiting | + | |
| - | | ::: | RED strobe (1.3s off and 0.3s on) – Unavailable | | + | |
| - | | LINE | Telephony gateway indicator | + | |
| - | | ::: | OFF – Not in use | | + | |
| - | | ::: | Slow RED flash – Dialing / ringing | + | |
| - | | ::: | Fast RED flash – Extension selection | + | |
| - | | ::: | Steady RED – In use | | + | |
| - | | ::: | RED strobe (1.3s off and 0.3s on) – Unavailable | | + | |
| | USB | USB memory stick connected | | | USB | USB memory stick connected | | ||
| - | | ET1-ET4 | Ethernet interface connected | | + | | ET0-ET4 | Ethernet interface connected | |
| + | <if et==4> | ||
| | WAN | Status of the Internet connection | | | WAN | Status of the Internet connection | | ||
| + | </if> | ||
| Light - The interface is connected. | Light - The interface is connected. | ||
| Line 26: | Line 19: | ||
| Blinking - Indicates that data is being sent or received. | Blinking - Indicates that data is being sent or received. | ||
| + | ===== Keys ===== | ||
| + | Three buttons allow you configure the unit: | ||
| ^ Keys: ^^ | ^ Keys: ^^ | ||
| - | | SET | Press and hold for two seconds to enter the set-up mode | | + | | SET | Press and hold for three seconds to enter the [[settings_and_administration: |
| - | | SEL | Press to select between different displays/ | + | | SEL | Press to select between different displays/ |
| - | | ALT | Press to select firewall security profile. Press and hold for two seconds to allow remote configuration. | | + | | ALT | Press to select firewall security profile.\\ Press and hold for three seconds to allow [[web_gui: |
| - | :!: Keys can be disabled on the [[web GUI: | + | :!: Keys can be disabled on the [[web GUI:Administration page#Front Panel Buttons|Administration page]]. |
| - | ^ Display: ^^ | + | By keeping some buttons pressed during power on unit can enter [[product overview: |
| - | | AD | Displays IP address | + | |
| - | | CFG | Configure IP address | + | ===== Display |
| + | The 3-digit display shows [[display|status]] and allows [[settings_and_administration: | ||
| + | Above and to the right of the 3 digits are small text indicators showing what is currently displayed: | ||
| + | ^ [[display|Normal]] mode: ^^ | ||
| + | | AD | - | | ||
| + | | CFG | Configuration has been changed without saving it permanently.\\ Powering off unit will result in loosing your changes. | ||
| | DHP | - | | | DHP | - | | ||
| - | | RST | Reset all configurations to factory defaults | + | | RST | Unit is in [[troubleshooting: |
| | LQ | Line quality (SNR margin) | | | LQ | Line quality (SNR margin) | | ||
| | TS | Transmit speed (Kbps) | | | TS | Transmit speed (Kbps) | | ||
| | RS | Receive speed (Mbps) | | | RS | Receive speed (Mbps) | | ||
| + | ^ [[settings_and_administration: | ||
| + | | AD | View IP address / View MAC address | | ||
| + | | CFG | Edit IP address / Save settings permanently | | ||
| + | | DHP | Read from USB | | ||
| + | | RST | Reset to factory defaults | | ||
| + | | LQ | Perform diagnostic test | | ||
| + | | TS | - | | ||
| + | | RS | Collect debug information | | ||
