Differences

This shows you the differences between two versions of the page.

--- product_overview:front_panel [2010/11/17 11:34] – tibor
+++ product_overview:front_panel [2011/08/17 10:16] (current) – tibor
@@ Line 8: / Line 8: @@
 | LINE	| Telephony gateway (FXO) indicator:\\ OFF – Not in use\\ Slow RED flash – Dialing / ringing\\ Fast RED flash – Extension selection\\ Steady RED – In use\\ RED strobe (1.3s off and 0.3s on) – Unavailable\\ \\ ADSL status indicator:\\ Slow GREEN flash - ADSL training\\ Steady GREEN - ADSL connected (FXO idle)\\ GREEN flicker - ADSL data sent or received |
 | USB	| USB memory stick connected |
-| ET1-ET4	| Ethernet interface connected |
+| ET0-ET4	| Ethernet interface connected |
+<if et==4>
 | WAN	| Status of the Internet connection |
+</if>
 Light - The interface is connected.
@@ Line 20: / Line 22: @@
 Three buttons allow you configure the unit:
 ^ Keys: ^^
-| SET	| Press and hold for two seconds to enter the [[settings_and_administration:front_panel_configuration|set-up mode]] |
+| SET	| Press and hold for three seconds to enter the [[settings_and_administration:front_panel_configuration|set-up mode]] |
-| SEL	| Press to select between different displays/values. Press for two seconds to cancel any set-up. |
+| SEL	| Press to select between different displays/values.\\ Press for three seconds to cancel and leave [[settings_and_administration:front_panel_configuration|set-up mode]].\\ Press for 10 seconds to turn [[wireless:start|wireless access point]] on or off. |
-| ALT	| Press to select firewall security profile. Press and hold for two seconds to allow [[web_gui:remote_config|remote configuration]]. |
+| ALT	| Press to select firewall security profile.\\ Press and hold for three seconds to allow [[web_gui:remote_config|remote configuration]]. |
-:!: Keys can be disabled on the [[web GUI:Administration page]].
+:!: Keys can be disabled on the [[web GUI:Administration page#Front Panel Buttons|Administration page]].
+By keeping some buttons pressed during power on unit can enter [[product overview:special modes]].
 ===== Display =====
-The 3-digit display shows status and allows [[settings_and_administration:front_panel_configuration|configuration]].
+The 3-digit display shows [[display|status]] and allows [[settings_and_administration:front_panel_configuration|configuration]].
 Above and to the right of the 3 digits are small text indicators showing what is currently displayed:
-^ Display: ^^
+^ [[display|Normal]] mode: ^^
-| AD	| Displays IP address  |
+| AD	| - |
-| CFG	| Configure IP address |
+| CFG	| Configuration has been changed without saving it permanently.\\ Powering off unit will result in loosing your changes. |
 | DHP	| - |
-| RST	| Reset all configurations to factory defaults |
+| RST	| Unit is in [[troubleshooting:safe mode]], using default values temporarily. |
 | LQ	| Line quality (SNR margin) |
 | TS	| Transmit speed (Kbps) |
 | RS	| Receive speed (Mbps) |
+^ [[settings_and_administration:front_panel_configuration|Configuration]] mode: ^^
+| AD    | View IP address / View MAC address |
+| CFG   | Edit IP address / Save settings permanently |
+| DHP   | Read from USB   |
+| RST   | Reset to factory defaults |
+| LQ    | Perform diagnostic test |
+| TS    | - |
+| RS    | Collect debug information |
-Read more about the [[display]].
-Read more about [[settings_and_administration:front panel configuration]].