Differences

This shows you the differences between two versions of the page.

--- product_overview:display [2010/11/17 11:44]
tibor
+++ product_overview:display [2011/09/05 10:25] (current)
tibor
@@ Line 1: / Line 1: @@
 ====== Display ======
-The display on the front panel presents information about the status of the Internet Gate and connected networks.
+{{:product_overview:display.gif?110 |display segments}}
+The display on the [[product_overview:front panel]] presents information about the status of the Internet Gate and connected networks.
 ===== Power on =====
@@ Line 8: / Line 11: @@
   - HELLO (scrolls across the display): Start sequence completed. Unit is working in normal mode.
-=== Special power on ===
+By keeping some front panel buttons pressed during power on unit can enter [[product overview:special modes]] that result in different display behaviour.
-== Lifeboat mode ==
-If you keep the **ALT** button pressed while turning the power on the unit will start in lifeboat mode.
 ===== Normal operation =====
@@ Line 26: / Line 27: @@
   - Three rotating 8: ADSL connection in progress (phase: line analysis)
 After the ADSL connection has been established the display enters normal operation mode.
+Each time the firewall stops a packet the small dot in the upper left corner of the display (below AD) is flashed.
+===== Unsaven changes =====
+CFG is lit on the display if there are settings in the unit not [[settings_and_administration:apply_and_save_permanently|saved permanently]].
 ===== Remote access =====
@@ Line 49: / Line 55: @@
 A rotating bar + IP : No WAN IP connectivity. WAN link is up, but WAN IP address (inside DHCP or PPP answer) has not been received yet.
-A rotating O + number : Progress counter counting up or down. Firmware upgrade or other operation in progress. Do not turn unit off before progress is finished!
+A rotating bar + number : Progress counter counting up or down. Firmware upgrade or other operation in progress. Do not turn unit off before progress is finished!
-Two rotating Os : Processing. Flash file system save or other operation in progress. Do not turn unit off while processing is displayed!
+Two rotating bars : Processing. Flash file system save or other operation in progress. Do not turn unit off while processing is displayed!
 Press SEL to install (scrolls across the display) : A new configuration has been loaded through provisioning. The user now must press SEL button to install it and reboot unit.
-Error messages
+===== Interface selection =====
+Depending upon special branding, some units may display "AdS" (not "Ad5") first time they are powered on. This special interface selection mode allows user to select what interface to use as WAN interface:
+  * "AdS" = ADSL interface
+  * "EtH" = ET0 Ethernet interface
+  * "FLA" = ET0 interface in Fiber LAN Access mode
+Select mode using the SEL button, then press SET to activate. Unit then reboots and "AdS" is no longer shown.
+===== Error messages =====
 “888" at power-on : Bootloader could not be loaded. Unit needs repair.
-IFC (during power-on boot) : Wrong IFC (Intertex Feature Code) found in unit. The unit will attempt to correct the IFC and reboot.
+IFC (during power-on boot) : Wrong [[:license|IFC]] found in unit. The unit will attempt to correct the IFC and reboot.
 LIC : Out of SIP [[:license|licenses]]. All SIP licenses are in use – more SIP licenses need to be bought to allow more SIP connections to be established. Purchase more SIP licenses using the “Buy Extras" button on the [[web GUI:login page]].
 E : A fatal error has occurred. The unit has crashed and needs to be turned off and on again. Debug information might have been collected of the event – check [[web GUI:Administration page]].

product_overview/display.1289990643.txt.gz · Last modified: 2010/11/17 11:44 by tibor

Show page Old revisions