Quick links:
Product Overview
Installation
Settings and Administration
ADSL
SIP Support
Telephone ports
Network
Firewall
Wireless
VPN
Misc
Licenses
Troubleshooting
Differences
This shows you the differences between two versions of the page.
|
product_overview:display [2011/01/26 14:34] tibor |
product_overview:display [2011/09/05 10:25] (current) tibor |
||
|---|---|---|---|
| Line 11: | Line 11: | ||
| - HELLO (scrolls across the display): Start sequence completed. Unit is working in normal mode. | - HELLO (scrolls across the display): Start sequence completed. Unit is working in normal mode. | ||
| - | === Special power on === | + | By keeping some front panel buttons pressed during power on unit can enter [[product overview:special modes]] that result in different display behaviour. |
| - | == Lifeboat mode == | + | |
| - | If you keep the **ALT** button pressed while turning the power on the unit will start in [[troubleshooting:lifeboat]] mode. | + | |
| - | == Factory defaults == | + | |
| - | If you keep **SEL** and **ALT** buttons pressed while turning the power on a reset to [[settings_and_administration:factory defaults]] is performed, and unit enters [[troubleshooting:lifeboat]] mode. | + | |
| - | == Safe mode == | + | |
| - | If you keep the **SET** button pressed while turning the power on, and keep it pressed until "SAFE" is shown in display, Internet Gate is started in [[troubleshooting:safe mode]], temporarily using factory default values. | + | |
| ===== Normal operation ===== | ===== Normal operation ===== | ||
| Line 37: | Line 31: | ||
| ===== Unsaven changes ===== | ===== Unsaven changes ===== | ||
| - | CFG is lit on the display if there are settings in the unit not saved permanently. | + | CFG is lit on the display if there are settings in the unit not [[settings_and_administration:apply_and_save_permanently|saved permanently]]. |
| ===== Remote access ===== | ===== Remote access ===== | ||
| Line 66: | Line 60: | ||
| Press SEL to install (scrolls across the display) : A new configuration has been loaded through provisioning. The user now must press SEL button to install it and reboot unit. | Press SEL to install (scrolls across the display) : A new configuration has been loaded through provisioning. The user now must press SEL button to install it and reboot unit. | ||
| + | |||
| + | ===== Interface selection ===== | ||
| + | Depending upon special branding, some units may display "AdS" (not "Ad5") first time they are powered on. This special interface selection mode allows user to select what interface to use as WAN interface: | ||
| + | * "AdS" = ADSL interface | ||
| + | * "EtH" = ET0 Ethernet interface | ||
| + | * "FLA" = ET0 interface in Fiber LAN Access mode | ||
| + | Select mode using the SEL button, then press SET to activate. Unit then reboots and "AdS" is no longer shown. | ||
| ===== Error messages ===== | ===== Error messages ===== | ||
| Line 71: | Line 72: | ||
| “888" at power-on : Bootloader could not be loaded. Unit needs repair. | “888" at power-on : Bootloader could not be loaded. Unit needs repair. | ||
| - | IFC (during power-on boot) : Wrong IFC (Intertex Feature Code) found in unit. The unit will attempt to correct the IFC and reboot. | + | IFC (during power-on boot) : Wrong [[:license|IFC]] found in unit. The unit will attempt to correct the IFC and reboot. |
| LIC : Out of SIP [[:license|licenses]]. All SIP licenses are in use – more SIP licenses need to be bought to allow more SIP connections to be established. Purchase more SIP licenses using the “Buy Extras" button on the [[web GUI:login page]]. | LIC : Out of SIP [[:license|licenses]]. All SIP licenses are in use – more SIP licenses need to be bought to allow more SIP connections to be established. Purchase more SIP licenses using the “Buy Extras" button on the [[web GUI:login page]]. | ||
| E : A fatal error has occurred. The unit has crashed and needs to be turned off and on again. Debug information might have been collected of the event – check [[web GUI:Administration page]]. | E : A fatal error has occurred. The unit has crashed and needs to be turned off and on again. Debug information might have been collected of the event – check [[web GUI:Administration page]]. | ||
