Quick links:
Product Overview
Installation
Settings and Administration
ADSL
SIP Support
Telephone ports
Network
Firewall
Wireless
VPN
Misc
Licenses
Troubleshooting
Differences
This shows you the differences between two versions of the page.
|
settings_and_administration:front_panel_configuration [2010/11/12 11:03] tibor created |
settings_and_administration:front_panel_configuration [2012/07/09 10:09] (current) tibor |
||
|---|---|---|---|
| Line 8: | Line 8: | ||
| Holding SEL button pressed 3 seconds at any time aborts configuration and immediately returns display into normal mode. | Holding SEL button pressed 3 seconds at any time aborts configuration and immediately returns display into normal mode. | ||
| + | |||
| + | Front Panel Configuration can be disabled on the [[web_gui:administration_page|Administration page]]. | ||
| + | <if ver lt 5.32> | ||
| + | //(Not available in releases prior 5.32)// | ||
| + | </if> | ||
| ===== AD - View IP address ===== | ===== AD - View IP address ===== | ||
| Line 21: | Line 26: | ||
| * After all four sections of the subnet mask has been specified the IP address and mask is saved in memory. | * After all four sections of the subnet mask has been specified the IP address and mask is saved in memory. | ||
| - | ===== DHP - Read from flash ===== | + | <if !media5> |
| + | ===== DHP - Read from USB ===== | ||
| Read configuration or flash image from attached USB memory.(Only shown if there is an /ix78 directory in attached USB memory.) | Read configuration or flash image from attached USB memory.(Only shown if there is an /ix78 directory in attached USB memory.) | ||
| * Press SET button to access USB memory stick. | * Press SET button to access USB memory stick. | ||
| Line 27: | Line 33: | ||
| * Press SEL to access USB memory stick again: | * Press SEL to access USB memory stick again: | ||
| * “FLI” is shown if there is an /ix78/flashimage.bin file of 8MB in size present on USB memory. Press SET to burn it into unit’s flash memory as a flash image file. | * “FLI” is shown if there is an /ix78/flashimage.bin file of 8MB in size present on USB memory. Press SET to burn it into unit’s flash memory as a flash image file. | ||
| + | </if> | ||
| ===== RST - Reset all settings to factory defaults ===== | ===== RST - Reset all settings to factory defaults ===== | ||
| * Asks “clear all?” and then displays “no”. | * Asks “clear all?” and then displays “no”. | ||
| - | * Press SEL button to change to “YES” and press SET to wipe out all your settings and restore them to factory defaults. | + | * Press SEL button to change to “YES” and press SET to wipe out all your settings, restore them to factory defaults, and reboot the unit. |
| - | * If holding ALT button pressed 3 seconds instead of pressing SEL above then “YES.” (observe the dot) is displayed instead. Pressing SET now will only reset the unit’s password to admin/admin, but keeps all other settings unchanged. | + | * If holding ALT button pressed 3 seconds instead of pressing SEL above then “YES.” (observe the dot) is displayed instead. Pressing SET now will only reset the unit’s password to admin/admin, but keeps all other settings unchanged. The unit will not reboot. |
| ===== LQ - Perform diagnostic tests ===== | ===== LQ - Perform diagnostic tests ===== | ||
| - | * Tests WAN and LAN connectivity. Any problems found are displayed as error codes. | + | Tests WAN and LAN connectivity. Any problems found are displayed as error codes. If no problems were found “Passed” is displayed. |
| * Press SEL button after each error code shown. | * Press SEL button after each error code shown. | ||
