Differences
This shows you the differences between two versions of the page.
|
web_gui:network_page [2010/11/25 17:13] mats |
web_gui:network_page [2011/04/04 16:09] (current) tibor |
||
|---|---|---|---|
| Line 7: | Line 7: | ||
| The default settings will work for users connecting to the Internet through an Internet Service Provider that distributes network settings automatically using DHCP. [[wp>DHCP]] | The default settings will work for users connecting to the Internet through an Internet Service Provider that distributes network settings automatically using DHCP. [[wp>DHCP]] | ||
| - | Advanced configurations (multiple IP addresses, multiple WAN interfaces, etc) are on a separate [[Advanced Network Configuration]] page, opened by a link at the bottom of the page. | + | Advanced configurations (multiple IP addresses, multiple WAN interfaces, etc) are on a separate [[Advanced Network Configuration]] page, opened by a link at the bottom of the page. You can read about some special configuration scenarios [[network:start|here]]. |
| {{ :web_gui:network_page.png?267|Network page in rel 5.30}} | {{ :web_gui:network_page.png?267|Network page in rel 5.30}} | ||
| Line 74: | Line 74: | ||
| The arrows in the back panel picture indicate which interfaces have which subnet. | The arrows in the back panel picture indicate which interfaces have which subnet. | ||
| - | ==== Used as ==== | + | ==== Interface usage ==== |
| - | Select how the contact will be used: | + | A dropdown box selects how the interface will be used by the firewall/router/bridge: |
| - | * inside - Connected computers will be protected by the firewall on a separate subnet (normal, recommended setting for most users). | + | * //inside// - Connected computers will be protected by the firewall on a separate subnet (normal, recommended setting for most users). |
| - | * outside - Unprotected. Inside interfaces will be protected from this interface by the firewall. (Only for the advanced user!) | + | * //outside// - Unprotected. Inside interfaces will be protected from this interface by the firewall. (Only for the advanced user!) |
| - | * [[:network:DMZ]] - DeMilitarized Zone - Special subnet for webservers: can access WAN, but no connection at all to LAN. [[wp>DMZ_(computing)|DMZ]] | + | * //[[:network:DMZ]]// - DeMilitarized Zone - Special subnet for webservers: can access WAN, but no connection at all to LAN. [[wp>DMZ_(computing)|DMZ]] |
| - | * blocked - Connector not used and is switched off. | + | * //blocked// - Connector not used and is switched off. |
| - | * isolated - Can only access WAN, but no connection at all to other LAN interfaces. (Same as DMZ.) | + | * //isolated// - Can only access WAN, but no connection at all to other LAN interfaces. (Same as DMZ.) |
| - | * off - Virtual access point is not used and is switched off. (AIR can not be switched off here - disable entire wireless on Wireless Settings page instead.) | + | * //off// - Virtual access point is not used and is switched off. (AIR can not be switched off here - disable entire wireless on Wireless Settings page instead.) |
| - | * %%-->%% ET1 - Bridged to ET1. Uses same subnet as ET1 port, see ET1 port settings for details. | + | * //%%-->%% ET1// - Bridged to ET1. Uses same subnet as ET1 port, see ET1 port settings for details. |
| - | * %%-->%% ipwanx - Bridged to an extra WAN interface. Open the extra WAN interfaces page to see/edit this port's settings. | + | * //%%-->%% ipwanx// - Bridged to an extra WAN interface. Open the extra WAN interfaces page to see/edit this port's settings. |
| As the [[:wireless:start|wireless]] interfaces are turned off by default you are recommended to enable them on the [[web GUI:Wireless page]] before you configure them on this page. | As the [[:wireless:start|wireless]] interfaces are turned off by default you are recommended to enable them on the [[web GUI:Wireless page]] before you configure them on this page. | ||
| + | |||
| + | ==== IP address ==== | ||
| + | **IP Adress** The unit's IP address on LAN. The unit can be reached by this address from your PC. | ||
| + | |||
| + | **Subnet Mask** States which of the IP address' digits that identify the subnet of your LAN.\\ | ||
| + | :?: The more advanced user may want to enter subnet mask as a prefix length, where 255.255.255.0 is entered simply as the value "24" (the mask has 24 binary one:s). | ||
| + | This can be done here, as on many web pages in the Internet Gate where a subnet mask is requested. | ||
| + | However, the mask will be converted and stored in its dot notation form, and showed in this style the next time the web page is displayed. [[wp>IPv4_subnetting_reference|IP subnetting, CIDR]] | ||
| + | |||
| + | ==== DHCP Server ==== | ||
| + | This should be checked if you want the unit to act as a DHCP server on your LAN. (Recommended and default)\\ | ||
| + | (A DHCP server supplies IP addresses to all PC's on a LAN. [[wp>DHCP]])\\ | ||
| + | :!: It doesn't work to have more than one DHCP server on the LAN, make sure that other DHCP servers (in another Internet Gate, router or PC) are shut off. | ||
| + | If a DHCP server elsewhere on the LAN is preferred, this checkbox should be unchecked. | ||
| + | |||
| + | **From**, **To** The address range used by the DHCP server to select IP addresses to distribute.\\ | ||
| + | :!: The address range must lie within the subnet specified by the **IP Address** and **Subnet Mask** for this interface. [[wp>IPv4_subnetting_reference|IP subnetting]] | ||
| + | |||
| + | |||
| ===== Advanced settings ===== | ===== Advanced settings ===== | ||
| + | [[network:start|Special scenarios]] | ||
| + | |||
| [[Advanced Network Configuration]] | [[Advanced Network Configuration]] | ||
